Skip to content
Homemade one-person deer blind with red board-and-batten siding, a metal shed roof and plexiglass front and side windows, sitting on skids in the pines in Gratiot County, Michigan

Deer · Free DIY Plans

DIY Deer Blind Plans: Our One-Person Box Blind

The first blind we built on our 30.5 acres, measured with a tape and drawn up as free printable plans. Cut list, materials, drawings and every step.

The Quick Answer

A good one-person deer blind is about 53 inches wide and 50 inches deep, roughly 80 inches tall at the front and 98 at the back with a shed roof. It is framed with 2x4s, sits on two 4×4 skids, and has a 30″ x 14″ front window and an 18″ x 14″ window on each side, all with the bottom edge 40 inches off the floor. That is the blind in these plans, and it is the one we hunt from.

Homemade one-person deer blind with red board-and-batten siding, a metal shed roof and plexiglass front and side windows, sitting on skids in the pines in Gratiot County, Michigan
Our one-person blind: 53″ wide, 50″ deep, on two 4×4 skids in the pines.

We built this little red blind ourselves, for one person and one folding chair. It sits back in the pines on our land in Gratiot County, Michigan. When we decided to share the plans, we went out with a tape measure and measured every wall, window and door, so the numbers below come from a real blind, not a drawing that was never built.

It is a simple shed-roof box: board-and-batten siding painted barn red, a metal roof, plexiglass windows, a door on the back and an OSB-lined inside that keeps it dark. Two people can build it over a weekend or two with ordinary carpentry tools. Printed out and wrapped with a lumber yard gift card, these plans make one of our favorite gifts for hunters.

Deer Blind Size and Dimensions

For one hunter, you want enough room to sit in a normal chair, turn a little and raise a rifle or crossbow without bumping a wall. Our blind gives you about 18 square feet of floor, which is plenty for one adult and a pack.

53″Wide (front)
50″Deep (side)
80″ / 98″Tall, front / back
40″Floor to window sill
26¼” x 82″Door, back wall
53″80″30″ x 14″40″ floor to sillFRONT18″ x 14″50″98″SIDE (door is on the back wall)
Front and side views of our blind. The low side of the roof faces the deer; the door is on the tall back wall.
PartMeasurementNotes
Footprint53″ wide x 50″ deepOutside of the walls
Height80″ front, 98″ backMeasured from the ground; shed roof slopes toward the front
Front window30″ wide x 14″ tallCentered, bottom edge 40″ off the floor
Side windows (2)18″ wide x 14″ tallOne on each side, bottom edge 40″ off the floor
Door26¼” wide x 82″ tallCentered on the back wall
BaseTwo 4×4 skids, 50″ longLaid flat, with a treated 2×4 floor frame on top
RoofMetal panelsOver a 1/2″ OSB deck

Materials and Cost

Everything comes from a regular lumber yard. Use treated lumber only where wood touches the ground or the floor frame; the walls and roof can be standard 2x4s.

Base and floorOne treated 4×4 (10 ft) for the skids, four treated 2x4s (8 ft) for the floor frame, and 3/4″ exterior plywood for the deck.
Walls and roofAbout thirty 2x4s (8 ft), siding (T1-11, or boards and battens like ours), 7/16″ OSB to line the inside, 1/2″ OSB for the roof deck, two metal roof panels and drip edge.
Windows and doorOne 36″ x 48″ sheet of plexiglass, 1×3 trim, a 1×4 Z-brace for the door, strap hinges and a hasp.
InsideA rubber stall or garage mat for a quiet floor, a folding chair, and dark paint if you skip the OSB lining.

What it costs: plan on roughly $600 to $900 in materials at today’s lumber prices. Siding is the biggest swing: rough-cut boards from a local sawmill cost far less than T1-11 sheets, and the OSB lining is optional. Prices vary a lot by area, so price your list at your own yard before you start. The printable plans include the full shopping list with quantities.

Cut List

All 2×4 sizes are actual lumber (1-1/2″ x 3-1/2″). The framed walls are 68″ tall at the front and 86″ at the back; the floor frame and skids add about 7-3/4″ underneath, which brings the blind to its 80″ and 98″ overall heights.

PieceSizeQtyNotes
Skids (4×4 treated)50″2Laid flat, front to back
Floor rims (2×4 treated)53″2Front and back of the floor frame
Floor joists (2×4 treated)47″4Between the rims
Floor deck (3/4″ plywood)53″ x 50″1Seam over a joist
Front wall plates53″2Top and bottom
Front wall studs65″4Two at the ends, two beside the window
Front window sill and header30″2Opening 30″ x 14″
Back wall top plate53″1
Back wall bottom plates13″2Left and right of the door
Back wall studs83″4Two at the ends, two beside the door
Door header27″1Door opening 27″ x 83″
Side wall bottom plates43″2Fit between the front and back walls
Side wall top plates46-5/8″2Both ends cut at 22-3/4°
Side wall studs65-1/2″ to 82-7/8″8Angled tops; mark each one in place
Side window sills and headers18″4Openings 18″ x 14″
Rafters63″3Both ends cut at 22-3/4°
Roof deck (1/2″ OSB)59″ x 63″1One sheet plus a strip
Plexiglass32″ x 16″ and two 20″ x 16″31″ bigger than each opening

The PDF has every piece, including the window cripples and the exact long-point length of each side-wall stud, plus framing drawings for each wall.

How to Build a Deer Blind, Step by Step

  1. Level the skids. Set the two 4×4 skids flat where the blind will sit, about 45″ apart outside to outside. Dig or shim until they are level. Patio blocks under the ends keep them off wet ground.
  2. Build the floor. Screw the treated 2×4 rims to the four joists, square the frame by matching the diagonals (about 72-1/2″), set it on the skids and screw it down. Add the 3/4″ plywood deck.
  3. Frame the front wall. Lay it out flat on the deck: 53″ plates, 65″ studs, and a 30″ x 14″ window opening centered with the sill 40″ up. Screw it together, then stand it on the front edge of the floor.
  4. Frame the back wall. Same method with 83″ studs and a 27″ x 83″ door opening in the middle. Stand it on the back edge and brace both walls plumb.
  5. Fit the side walls. Measure the gap between the front and back walls (it should be 43″) and build each side wall to fit, with a sloped top plate and an 18″ x 14″ window centered with the sill 40″ up.
  6. Set the rafters. Cut three 63″ rafters with 22-3/4° ends and set them on the front and back top plates, one over each side wall and one in the middle. Toe-screw them and add hurricane ties.
  7. Roof it. Screw down the 1/2″ OSB, add drip edge on the front and back, then the metal panels with roofing screws through the high ribs.
  8. Side and paint it. Hang the siding, trim the corners and paint it a dull color. Line the inside with OSB if you want it darker and quieter.
  9. Add the windows. Cut the plexiglass 1″ bigger than each opening and hold it from the inside with 1×3 trim. Leave the protective film on until it is cut.
  10. Hang the door and finish the floor. Cut the door from siding, brace it with a 1×4 Z on the inside, hang it on strap hinges and add a hasp. Lay the rubber mat, bring in a chair and brush in the outside.
Inside of a homemade one-person deer blind with OSB walls and ceiling, a rubber mat floor, a red folding chair and plexiglass front and side windows
Inside ours: OSB-lined walls, a rubber mat floor and room for one chair.

Windows: Plexiglass, Height and Shooting

Both of our blinds have plexiglass windows. Plexiglass keeps the wind, rain and snow out, holds in a little warmth on cold mornings, and cuts down how much of your scent drifts out the front.

Never shoot through it. Plexiglass can deflect a bullet or an arrow. The easiest fix is a flip-down window: hinge the plexiglass panel along the bottom and hold it shut with small wooden turn buttons, so it drops open without a sound. Some of the windows on our own blinds work this way. The other option is a removable pane, held in with turn buttons instead of screws, that you lift out quietly when a deer is coming in. A 40″ sill puts the bottom of the window at about chest height when you sit in a normal chair, so you can rest a rifle on the sill.

Keep the inside dark. Deer pick up movement in a bright window far more than they notice the blind itself, which is one more reason we like the OSB lining.

Where to Put Your Blind

  • Wind in your face. Set the front of the blind so the wind usually blows from the deer toward you during the hours you hunt.
  • Sun behind you. Morning and evening sun shining straight into the windows lights you up and blinds you.
  • Walk in from behind. With the door on the back wall, you never cross the field you are watching to get in.
  • Set it early. Get the blind in place a few weeks before season and brush in the sides so deer get used to it.
  • Near food and water. Face the blind toward where deer feed and drink. If you are planning a plot to hunt over, our deer food plots for beginners guide covers what to plant and when.

Because it sits on skids, you can drag the blind to a new spot with a tractor or truck, which is handy when the deer change their patterns. Check your state’s blaze orange rules for hunting from a ground blind during firearm season.

Back wall of a red homemade deer blind with a tall board door, under pine trees in Michigan
The door is on the tall back wall, so you walk in from behind.

Upgrades Worth Copying

We looked at a camo-sided blind at a dealer, and it had a few ideas worth stealing for your own build.

  • Flip-down windows. Some of the windows on our own blinds flip down on hinges, and so did this one. A plexiglass panel hinged along the bottom and held shut with small wooden turn buttons opens silently when a deer steps out. It’s the simplest answer to “never shoot through plexiglass.”
  • Tall, narrow side windows. A bow hunter needs vertical room to draw. A narrow window that runs taller than the regular ones gives you that without opening up the whole wall.
  • Camo siding. Camo-pattern siding hides a blind against the woods better than plain paint, especially in open timber.
  • Lined walls. The inside was lined, which keeps it darker and quieter, the same reason we line ours with OSB.
Box deer blind with camouflage-pattern siding, a metal roof and several plexiglass shooting windows, sitting on treated skids
A camo-sided blind we looked at at a dealer.
Inside a deer blind with lined white walls, rough-sawn framing, a plank floor, hinged flip-down plexiglass windows and tall narrow side windows
Flip-down windows on the front, tall narrow ones on the sides.
Close-up of a hinged flip-down plexiglass deer blind window held shut by small wooden turn buttons, next to a tall narrow side-hinged window
Wooden turn buttons hold the flip-down window shut.

When the Kids Want to Come Along

Here is something that happens to a lot of hunters: you build a one-person blind, and then you find out someone in the family, often a kid, would love to come hunting with you. Getting kids out in the woods is one of the best things you can do for them, but a 53-inch box with one chair gets tight fast.

That is why we also built a bigger blind with room for two, and honestly three. It is 76″ x 73″ with a peaked metal roof, plexiglass windows on three sides (two 40″ x 16″ side windows and a 30″ x 16″ front), a 24″ x 73″ door, and it sits 12″ off the ground on 4x4s with a treated 2×4 floor. If you have kids who want to come along, build the bigger one first. Plans for that one are coming next.

Homemade wooden two-person deer blind with a green metal roof and plexiglass windows under pine trees in Michigan
Our bigger family blind: room for two adults, or one adult and two kids.

Our Trick for Keeping Kids Busy

We put little suet cakes around our blinds so we can watch the birds and tell the kids what kind of birds are coming in. In fall and winter, suet brings woodpeckers, chickadees and nuthatches right up to the windows, and a slow morning turns into a game of naming every bird. Hang the suet in a cage on a tree trunk, up off the ground. Michigan bans baiting and feeding deer in the Lower Peninsula, so keep it where deer cannot reach it.

Want to know which birds you are looking at? Our guide to what birds eat covers suet and the birds it brings in, and the deer guide has everything else for the young hunter in your life, from reading deer tracks to when deer move.

Print the Plans and Take Them to the Lumber Yard

The PDF has the full shopping list, cut list and framing drawings for every wall. Free — enter your email and we’ll send it to you.

⬇ Get the Free Plans

Common Questions

How big should a one-person deer blind be?

About 4 by 4 feet inside is the minimum for one adult in a chair. Ours is 53″ x 50″ outside, which gives enough room to turn and shoot without hitting a wall. For two or three people, go to about 6 by 6 feet.

How much does it cost to build a deer blind?

Roughly $600 to $900 in materials for a framed box blind like ours, depending mostly on the siding you choose and local lumber prices. Rough-cut boards from a sawmill can bring that down a lot.

How high should deer blind windows be?

For a seated hunter, put the bottom of the window about 40 inches off the floor. That puts the sill around chest height in a normal chair, so you can rest a gun on it. Ours are 14 inches tall, which is enough to see and shoot without showing much of yourself.

Should deer blind windows be plexiglass or open?

Plexiglass keeps out wind and weather and holds in scent, but never shoot through it. Make at least the front pane flip down on hinges or lift out, so you can open it before the shot.

How long does it take to build a deer blind?

With two people and basic tools, plan on one to two weekends: one day for the floor and framing, and the rest for the roof, siding, windows and door.

Should a ground blind sit on skids?

We like skids. They keep the floor off the wet ground so it lasts longer, and they let you drag the blind to a new spot. Use treated 4x4s and put patio blocks under the ends.

Can I take my kids hunting in a blind?

Yes, and a blind is one of the best ways to do it, since kids can move around a little without being seen. A one-person blind is too tight, so build or bring a bigger one. Check your state’s youth hunting and mentored hunting rules.

Sources

Private Lands Wildlife is a family-run 30.5-acre wildlife habitat in Gratiot County, Michigan. These plans are drawn from a blind we built and use; check them against your own build and local rules before you cut.

Leave a Reply

Your email address will not be published. Required fields are marked *